Maytag washer keeps spinning for various reasons like a faulty driver belt, defective motor control board, and a worn-out clutch band kit Your washer might be stuck in the spin or rinse cycle when you use excess power detergent, timer issues, drain control issues, and electrical problems
Why is my washer stuck on the wash cycle?
If your top load washing machine (or some older front load washers) is stuck on one continuous cycle and will not advance and forward to the next wash cycle, then most likely the washer timer is faulty and needs replacement The timer on your washing machine controls all aspects of the wash, spin, and rinse cycles
How do I reset my Maytag washing machine?
If an error message causes your Maytag washer to not run properly, reset the washer to clear the error messageHow to Reset a Maytag Washer Press the “Power/Cancel” button Push the appropriate button to choose a new cycle Press “Start/Pause” You have now reset your Maytag washer
How do you reset the wash cycle on a washing machine?
To reset your washing machine, unplug it from the power outlet Then, plug the washer cord back into the wall Finally, open and close the washing machine door six times to send the reset signal to the system components
How do you fix a washing machine that is stuck on the rinse cycle?
To Fix: Check all the draining parts on the washer Check that the drain hose is not clogged or kinked Reposition the drain hose so the washer does not have issues draining out the water Check the drain pump to be sure it operates correctly and is not jammed with foreign objects
Do washing machines have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault Some machines have a button you push to reset its motor On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it
Why won’t my Maytag washer drain and spin?
One common cause why a Maytag top load washer won’t spin is due to an uneven load or jammed clothing Larger items or loads tend to settle on one side of the washer drum during a cycle Try to redistribute the load or remove a few articles of clothing and run the spin cycle on your washer again
Why do I have to unplug my washer to restart it?
This is an indication that the door switch is malfunctioning, and not telling the control that the door has been opened If you don’t open the door the control won’t start another cycle The only thing you are doing when the power is off is to reset the controls memory
Why won’t my washer rinse and drain?
The most probable cause is a clogged pump filter The pump filter should be cleaned every three months or when it’s clogged To clean the pump filter, open the cover to expose the filter Some washing machine models have a small hose stuck behind the cover to drain the water inside the filter
Why is my washer not stopping?
The reason your washer will not stop filling could be because the hose has either clogged, fallen off, or gotten a hole in it If there is a hole in the hose, it will reduce the pressure and cause the water level switch not to shut off power to the water inlet valve
What are the codes for a Maytag washer?
Error Codes in my Maytag Front Load Washer Error Code Error Sud or Sd There are too many suds in the washing machine F5 E2 The door is not locking properly F7 E1 Indicates a motor speed sensing error, F8 E1 or LO FL The washer is sensing a low flow of water
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining
How do I reset my Maytag Bravos washer?
Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine Press “Start/Pause” I have a maytag bravos xl, every … Unplug the washer for 1 minute from the electrical outlet If the door lock switch does not engage fully, the washer will not move into the high spin mode
How do you reset the code on a washing machine?
How to reset the washing machine: Press POWER to turn the washer off Unplug the washer from the power outlet or turn the circuit breaker to the unit off With the power disabled, press and hold the START/PAUSE button for 5 seconds Plug the washer back in, or turn the circuit breaker back on
How do you force drain a Maytag washer?
Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections Scoop out any remaining water in the washer drum Unhook the drain hose from the wall or sink drain and empty residual water into a bucket
Why is my Maytag Centennial washer stuck on sensing?
If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light
What are common problems with washing machines?
Common Washing Machine Problems and Solutions Vibrating Washer Leaky Washer Noisy Washer Washer Won’t Run Washer Won’t Drain Detergent Won’t Dispense Smelly Washer
How do you unlock a Maytag commercial washer?
Washer door unlock fix: Cancel the wash cycle, wait for it to drain the water and the door should unlock, OR pull the green string near the detergent area, OR pull the lever on the bottom of the door switch, OR unplug the washer for 5 minutes to reset These 4 things should unlock your washers door
How do you reset the code on a Maytag Centennial washing machine?
To exit the Maytag Centennial diagnostics press and hold the “start” button for about 3 seconds (Again This will erase error codes in the Centennial washer’s memory) Now you can do run a Maytag Centennial automatic diagnostic washer cycle