P-tex is a tradename for the polyethylene base material used on skis and snowboards Sintered p-tex is made by packing ultra high molecular weight polyethylene powder into a cake that is heated and compressed (sintered) to form a log or billet (see diagram below)
How do you use P-Tex?
Fill in the Gouge Using your propane torch or butane lighter, fire up one tip of the P-Tex candle Wait until it’s flaming (this may take a couple of minutes) Move the molten P-Tex candle to the gouge Do a second round if necessary then extinguish the flame Let the P-Tex cool about 15 minutes
What is made of PTEX?
P-tex is the abbreviated name for Polyethylene There are 10 major classifications of Polyethylene For snowboards and skis the form used is UHMWPE or Ultra-high-molecular-weight polyethylene It’s the same material used to make bullet proof jackets as well as hip and knee replacements
Does PTEX absorb wax?
Often referred to by the trade name p-tex, it’s a strong and impact-resistant substance with a low friction coefficient Because p-tex is porous, almost like a sponge, it can absorb wax time and time again
What is P TEX work?
P-tex is a tradename for the polyethylene base material used on skis and snowboards Sintered p-tex is made by packing ultra high molecular weight polyethylene powder into a cake that is heated and compressed (sintered) to form a log or billet (see diagram below)
Can you PTEX a sintered base?
Sintered is more expensive because it’s more durable, it glides better and it holds wax better Generally, you’d be advised to repair a base with the same materials it’s been crafted with, but you can’t actually buy sintered p-tex to fix your base
How do you fix epoxy on a snowboard?
Slowly spread a good dollop of epoxy in the wound Then grab a hairdryer and start heating the epoxy so it liquefies and seeps into the core Keep heating the board’s base, sidewall, topside and the epoxy until the epoxy stops bubbling from the escaping air Be careful not to melt your base or topsheet
What are snowboard bases made of?
Polyethylene is the main and often sole ingredient that snowboards bases are made from The water-repellent, highly porous and abrasion-resistant attributes of the material make it perfect for sliding on snow Molecular mass and density of the polyethylene determine the performance of the base
Can you use a hot glue gun for PTEX?
No HTML is allowed they do make hot glue gun like tools for ptex, but you cant really use just a hot glue gun as glue sticks melt at a much lower temp so the guns don’t get very hot
Do you need to wax after PTEX?
Definitely before waxing As you thought, PTEX candles are made of the same material as the base is made of so you want the clean the gouge area of any dirt, debris or wax if you can lightly sand the area to give the new PTEX material some surface to stick on to
Can I use car wax on skis?
What you need is a wax that will work on the plastic base of the ski, is designed to work in very cold temperatures, and stay on even with abrasion (such as you get when skiing), so I wouldn’t use a car wax
Why does wax make skis faster?
Waxed Skis are More Fun Wax makes your skis hydrophobic, or water resistant The more hydrophobic your skis, the faster they will be down the slopes Keeping your skis waxed will also make them easier to make smoother turns
How do you fix a core shot?
How To: Fix A Core Shot Clean it up Cut away hangnails and bulges in the base and avoid slicing straight lines and blunt edges Scuff it up Scuff up the damaged area with sandpaper or a wire brush, then wipe away any debris with a cloth and some base cleaner Seal er Finish
Can you replace ski edges?
It is possible to replace sections of edge but it’s major surgery requiring the p-tex to be cut back & then patching in once the edge has been replaced
What is ski base cleaner?
Swix aersol base cleaner is the proper base cleaner to clean your ski and board bases before waxing Using anything else can leave a residue which would get waxed into your bases damaging them The Swix base cleaner will quickly remove wax residue and slope grime from ski and board bases without damaging the bases
What is a core shot on skis?
A core shot is when the core of the ski is exposed to the elements (water, moisture, snow etc) instead of being protected Moisture getting into the core of the ski is bad, that moisture can freeze too, so let’s talk about how to fix it Core shots are the most tricky and require the most work
Are scratches on a snowboard bad?
scratches will affect your boards performance big scratches will need to be filled with p-tex, which is plastic (either sticks or granular) which is melted into the deep scratches
Can I ski with a core shot?
A gouge becomes officially classified as a “core shot” when it rips through the P-Tex base and exposes the ski’s core This type of ding is especially detrimental to the ski because it allows moisture to penetrate the core, and in skis with a wooden core, this could potentially lead to rot within the ski
Does PTEX stick to metal?
Ptex doesn’t stick to metal very well a short cut is just to use copolymer It holds up pretty well Not as hard are normal ptex but harder than drip stuff
What kind of plastic is PTEX?
SINTERED BASE UHMW PE is Ultra High Molecular Weight plastic It might also called Ptex by some manufacturers It is very strong and durable plastic, comparable to Sintered base! Sintered bases come in numbers of IS7200 and up, indicating the density