How do I know if my lawn mower spindle is bad?
The Four Signs the Spindles are Malfunctioning The Lawn Will Have Uneven Cuts The first and most noticeable problem when the spindles go out is the yard is cut uneven There Will Be a Squealing Noise If There is Vibration and Buzzing Noises Broken or Bent Parts Can Mean the Spindle is Worn
Can you mow with a bad spindle?
If the spindle looks bent or broken, then it needs to be replaced You will feel how the blades start to move unevenly and cut your grass in a disorganized way In some cases, the blade won’t spin at all or instead make loud cracking noises
How often should you grease mower spindles?
The spindles and caster wheels are generally the most often greased The spindles and castor wheels should be done around once a month because of the moving interior parts Commercial mowers that put hundreds of hours on their Ferris mower would be looking at greasing the mower everyday depending on usage
How do you remove a spindle?
Lay a thin hand saw blade on the tread of the stair so that its teeth are where the bottom of the spindle and the top of the tread meet A little wooden dowel pin connects the two together Move the saw back and forth to slide under the spindle and cut the dowel pin Repeat this process for each spindle
Do lawn mower spindles come greased?
Registered They do not come packed from the factory, that is a common misconception When I worked for a Deere dealer it was not uncommon to have to change all the spindles, idler pulleys, and deck belt at ~150 hours On a three blade deck it would often take an entire tube of grease to fill the new spindles
How do you remove a pulley from a riding lawn mower?
Place a wrench onto the square end of the threaded screw and turn it clockwise As you turn it, the jaws pull the pulley up and off the spindle
How do you remove a pulley from a lawn mower deck?
Spray a liberal amount of penetrating oil onto the front and back sides of the pulley hub until they are thoroughly soaked Spray the pulley retaining bolt and pulley shaft with the oil Allow about 30 minutes to two hours for the penetrating oil to loosen the rusted pulley and other parts
What is a spindle on a riding mower?
The spindle on a riding mower is the post to which the blade attaches and around which it spins when the machine is in action A riding mower may have one or more spindles, depending on the size of the mower and the way it is manufactured
How does a mower spindle work?
The spindles on a riding or commercial walk-behind mower are attached to the cutting deck and work with the pulleys to turn the blades below the deck so grass can be cut Mowers, such as the John Deere D100 series, require only a shot or two of grease periodically
Why does the belt keep coming off my riding lawn mower?
The drive belt may come off a riding mower because it is damaged or loose If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary
What causes a riding lawn mower to cut uneven?
Uneven cutting is usually caused by mower deck damage or misadjustmentUneven Cutting CAUSE SOLUTION Deck is not leveled correctly Level the deck correctly Blades are dull or worn Sharpen or replace the blades Blades are damaged Replace the blades Deck is clogged with grass clippings Clean out the deck
Do mower spindles get hot?
My spindles get so hot that they’re burning my fingers after 3 seconds of touching This is touching the pulley from the top Both are about the same temp, so I’m assume it’s normal Doesn’t take long this is only after mowing for 10 minutes
How long do lawn mower spindles last?
Member The maintenance free spindles usually last about 2-3 years in commercial use
How much is a new spindle?
The price, including labor, to replace a full set of spindles can range anywhere from $1,200 to $1,600Cost to Replace Stair Banisters Banister Material Price Per Linear Foot (Including Labor) Aluminum $70-$80 Wood $30-$75
How much does it cost to fix a spindle?
There are many factors that can significantly impact the cost of the repair For instance, a damaged tool interface may add between $700 and $1,600 depending on the size and style Damaged bearing journals can add between $400 and $1,400 A damaged shaft can add $4,000, often doubling the cost of a base repair
Can you replace spindle on torsion axle?
If you have an Eliminator Torsion axle you can replace the spindle If the torsion arm is exposed on the backside, you can place the castle nut back on the spindle so that it is even with the end of the spindle, and then hitting the rear of the spindle to force the spindle loose
Do I need to grease mower deck?
Lubricating the mower deck prevents creaking If you don’t lubricate the mower deck’s grease fittings, the mower may encounter problems such as jamming, unnecessary wear to deck components or possibly even damage to the shafts in the mower deck that turn the blades
What is a spindle bearing?
Spindle bearings are single row angular contact ball bearings which support thrust loads in one direction and are often used in machine tool spindles At very high speeds, spindle bearings can simultaneously absorb high radial forces and single direction axial forces
How do you remove a pulley without a puller?
If you’re adamant that you want to do it without the puller tool, here’s how: With the pump taken off the vehicle, place it in a vice and use a piece of metal pipe and a hammer to tap the wedge between the pulley and the pump Heat the center of the pulley with the blowtorch and pull it off
How do you remove a pulley from a keyed shaft?
To tighten the screw at the end of the gear puller, use the sockets wrench Continue until the pulley is free You can try to loosen the pulley by hitting the exposed end with a hammer