How do you use a John Deere riding lawn mower?
How do you engage a John Deere lawn mower?
How to Engage Lawn Mower Blades on a John Deere Turn the key to the “on” position, advance the throttle to half speed and allow the engine to warm up for 2 minutes Lower the mower to the desired cutting height Engage the mower blades; push the lever to the right of the steering wheel all the way forward
How do you drive a riding lawn mower?
How to Drive a Riding Lawn Mower Put the ignition key in the ignition slot Shift the lawn mower to a low gear using the shift lever and drive the lawn mower towards your lawn Stop the lawn mower when you reach your lawn by pressing the brake and clutch at the same time
Where is the choke on a John Deere riding lawn mower?
Move the throttle located to the left of the steering wheel into the choke position if the engine is cold Move it into the half-speed position if the engine is warm Some models of riding mowers have a choke knob instead of a choke position on the throttle
How do you turn on a riding lawn mower blade?
To engage the blades on a riding lawn mower that’s manually operated, turn the key clockwise to power it on, increase the throttle to half speed, and allow the engine to warm up for two minutes Then, lower the mower to the preferred cutting height Push the lever to the right of the steering to engage the blades
Why won’t my mower deck engage?
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely Belt could have snapped also When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt
How do you change the gears on a John Deere riding lawn mower?
Push the throttle all the way up, and engage the mower blades This is done by either pulling a switch up or pushing a lever forward, depending on your model of John Deere riding lawnmower Push the clutch/brake pedal and shift into desired gear
How do you put a gear on a riding lawn mower?
If you need to change gears while mowing, you do not have to disengage the blades Simply push the brake and clutch pedal, shift to your new desired gear, and release the brake and clutch pedal Always wear long pants, safety glasses and hearing protection when operating a riding lawn mower to prevent bodily injury
Where is the clutch on a riding lawn mower?
Power takeoff (PTO) clutches are found on riding lawn mowers These clutches exist on the bottom of the mower’s engine assembly and control the flow of power to the mower’s cutting blades
How do you start a John Deere tractor?
If the John Deere lawn tractor engine is warm, pull out the choke halfway Hold the brake pedal down Move the throttle lever to the “Start” position Turn the key to start the lawn tractor
What are the controls on a tractor?
There are three common types of control devices used on tractors: Foot Controls—Pedals Hand Controls—Levers, Toggles, Switches, Knobs, and Buttons Combination Hand and Foot—Engine Throttles
What is the choke on a John Deere?
The choke on a John Deere lawn tractor aids the engine in a cold start When the throttle cable becomes out of adjustment, the choke may not be working
Where is the choke on a John Deere Zero Turn mower?
Pull up on the choke knob, if you’re starting the engine cold The choke knob is located on the same panel as the throttle, and is the knob closest to the front of the machine on your left hand side
Why is my riding mower not cutting?
Replace the riding mower blade belt The blade belt spins the blades to cut the grass A worn or broken drive belt won’t spin the cutting blades so your mower won’t cut the grass A worn blade belt can also cause mower deck vibration or uneven cuts Examine the blade belt regularly and replace it if it’s worn or broken
How do you lower the blade on a John Deere riding lawn mower?
Press down on the left side foot pedal and push down on the mower lift lock lever Release the pedal to lower the mower deck If the mower deck gauge wheels touch the ground, adjust them until the gauge wheel are no longer touching
Why does the PTO not engage?
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage The PTO clutch is not repairable—if the clutch is defective, you must replace it The PTO switch provides power to the PTO clutch If the PTO switch is defective, replace it
What does the PTO switch do?
The PTO is a switch or lever found on tractors and mowers and stands for Power Take Off This can be an electric switch or mechanical engagement that takes engine power to operate the mower deck or an implement
What is a PTO clutch?
Power take-off (PTO) clutches provide a mechanical disconnect between the power created by gas and diesel engines or electric motors to another piece of equipment The PTO clutches enable the transmission of that energy to auxiliary equipment that does not generate its own power
How do you lower the blade on a riding lawn mower?
Lowering Lawn Mower Blades Riding mowers usually have their height adjustment levers or knobs on the left side by the seat Simply pull the lever toward the back or turn the knob counterclockwise Whenever you are adjusting lawn mower blade height levers, be sure that they lock into position before proceeding
How often should mower blades be sharpened?
This keeps your mower in good shape and helps to maintain a healthy lawn However, if you mow more often, the blades will need more attention On average, a mower blade should be sharpened after every 20 to 25 hours of use time