Depth ranges of 10,000 feet are standard with these broadband devices, which include sounders from all of the major brands
Can you run two depth finders at the same time?
Any time you run two units with the same frequency there is a risk of interference However, with the modern noise rejection systems built into today’s fish finders, in most conditions when there is a unit on the front and back of the boat with the same frequencies, they will not interfere with each other
What frequency should I use on my fish finder?
Frequencies commonly used by a conventional fish finder for recreational boat are 50 kHz (low frequency) and 200 kHz (high frequency) A lower frequency has a wider search angle and area Generally, the searchable angle of 50 kHz beams is approximately 50 degrees and that of 200 kHz beams is approximately 15 degrees
Can you run 2 fish finders off one transducer?
While it is not recommended that more than one transducer be run simultaneously, there can be multiple transducers installed on a boat For best results, two transducers need to have at least a 50 kHz difference in their frequencies to not cause interference
Do transducers interfere with each other?
If both transducers are using the same frequency, they will interfere with each other once you reach a water depth that allows the two beams to cross In shallow water, they may work together if the transducers are far enough apart Setting each unit on a different frequency will prevent interference
Can you put two fish finders on a boat?
You can have different brands of GPS/fishfinders, in fact you should not get interference while running both units with two different systems
Can two transducers be mounted side by side?
You can mount SI/DI and high speed transducers side by side on the same side of the boat without any problems When they both transducers use the same frequency is when you may experience interference
How far should a transducer be in the water?
Ensure the boat is in water greater than 2′ but less than the depth capability of the unit and the transducer is fully submerged Remember the sonar signal cannot pass through air If the unit is working properly gradually increase the boat speed to test high-speed performance
How does a fish finder get power?
Fish finders and other electronics need electricity to function On boats electricity is supplied from the batteries installed in the battery compartment Excluding special super compact fish finders, most fish finders use DC 12-24 volt power supply
What is chirp on a fish finder?
CHIRP stands for “Compressed High Intensity Radar Pulse” That’s a fancy way of saying it can show you fish that other forms of 2D sonar can’t By covering a wide range of frequencies, CHIRP produces more accurate, more detailed returns of fish, structure and the bottom
What does hard bottom look like on sonar?
When you see a hard bottom like gravel, chunk rock or shell beds, that bottom will be thick and yellow Whereas when you pass over a softer muddier bottom, the bottom will seem more translucent or darker red or blue
What is the easiest depth finder to use?
HOOK² 7 with TripleShot Transducer and US Inland Maps The world’s easiest-to-use fishfinder, HOOK² 7 TripleShot features Autotuning sonar, High CHIRP, SideScan and DownScan Imaging™ — all at a price that is easy to afford
Can you use a fish finder without a transducer?
LOWRANCE–Hook-7 Fishfinder/Chartplotter without Transducer Both CHIRP and Scanning Sonar: It’s compatible with both CHIRP and DownScan Imaging™, so you get the clearest view of fish, structure and the bottom
How close can you put transducers together?
Make sure there is nothing in front, behind, or to the side of the transducer that is closer than 12″ Do not mount the transducer where it could be damaged from trailering, launching, or storage
Can I run 2 transducers on HDS live?
You can use any combination of transducer sources you have on your network in either or both of those panels You can view the bow TM transducer and the rear skimmer transducer at the same time, on the same screen
Can a transom mount transducer be used with inboard engines?
Question: The installation manual says the transom mount transducer is not recommended for large inboard engines Answer: You can mount it on an inboard boat, but it is not optimal because of the turbulence created by the propeller
Can you run two transducers on a boat?
While it is not recommended that more than one transducer be run simultaneously, there can be multiple transducers installed on a boat For best results, two transducers need to have at least a 50 kHz difference in their frequencies to not cause interference
Can you put 2 transducers on a trolling motor?
Transducers do interfere with each other and it seems to get worse in deeper water Different brands may be ok If you had the same brand they say to adjust the ping speeds to different speeds to help with this
Can you mount a transducer too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer Using a transducer mounting plate makes this easy to do 5) Avoid mounting the transducer on the port side of the boat
Is it bad to run transducer out of water?
It is not recommended to run a FishFinder and transducer on a boat that is not in the water as you will not get any readings from the transducer Without the water, the transducer could burn out and have issues if left running for an extended period of time out of the water
How does a transducer work for a fish finder?
Sonars send out pulse of sound to locate objects Sound travels in waves, not straight lines, and these waves expand in cones, getting wider and wider Most sonars can control the range of the sound wave cone by changing the scanning beam frequency
Where is the best place to mount a transducer on a boat?
The location should be as close to the center of the boat as possible, but on the side of the downward swing the propeller On the majority of boats, this will be on the starboard (right) side
What is a transom transducer?
Transom mount transducers are affixed to the stern of your vessel, where smooth water flow is passing off the transom Designed for smaller outboard and inboard/outboard boats, these transducers are well suited to planing hulls