Wear on the outer flat side of the belt indicates a problem with an idler pulley More wear on one edge of the V-side than on the other indicated a drive pulley that is out of position and forcing the belt out of line
Why does my lawn mower drive belt keep coming off?
The drive belt may come off a riding mower because it is damaged or loose If broken or worn, the belt can break while the engine runs, and it can fly off at a great velocity, which is highly dangerous Check the belt for looseness, cracks, fraying or separation from the rest of the assembly, and replace if necessary
Why does my deck belt keep breaking?
the most common cause of the deck belt breaking would be a idler or mandrel pulley not lined up properly or the bearings going out and making the pulley wobble or the belt is getting rubbed somewhere check the pullies on the deck to make sure they turn freely and are not loose and wobbling around
Why does the belt keep coming off my Cub Cadet mower?
A Cub Cadet belt that is coming off your mower can be the result of bad bearings in your pulleys or spindle housing assemblies Take a look at each one of your pulleys Idler pulleys have a sealed bearing so the whole pulley needs to be replaced Your issue may be with the spindle housing assembly
Why does my belt keep coming off?
The serpentine belt need constant tension on the belt to keep it from coming off If the belt alignment is not aligned then the belt may come off When this is out of adjustment or the tensioner pulley itself is loose this may cause the belt to come off as you describe
Why does the belt keep coming off my Craftsman riding mower?
Your Craftsman mower belt may come off if the belt has been stretched or shredded; the belt keepers and brackets have been bent, the spindles, pulleys or tensioner spring are damaged; or debris has been lodged in your deck
How do you adjust a tensioner pulley?
Turn the adjustment bolt on the side, top or bottom of the pulley counterclockwise with the ratchet and socket until the accessory belt is loose enough to remove Tighten the tensioner pulley by turning the adjustment bolt clockwise with the ratchet and socket until the belt is tight
How often should I change the belt on my riding mower?
There’s no definite amount of time that a mower belt is supposed to last, but increased mower use shortens the interval in which a belt needs replacement Simply put, more use equals more wear Additionally, faulty belts or mechanical failures like a seized pulley can make lawn mower belts break prematurely
What causes a mower deck to vibrate?
Deck vibration can be caused by an unbalanced blade, worn pulley or mandrel, bad blade belt or debris caught inside a pulley Loose nuts or bolts on the pulleys, mandrels or blades can also cause vibration Remove the mower deck and re-tighten all fasteners
How long should a mower drive belt last?
Considering you are mowing 2 to 3 times the lawn of the typical homeowner, or 6 to 9 years worth, yeah, it could be worn Also consider the possible need for drive cable adjustment or engine rpm adjustment
How do you tighten the belt on a Cub Cadet mower?
Turn the ratchet toward the right side of the mower to loosen the belt tension on a 46-inch deck If your Cub Cadet lawn tractor has a 50-inch deck, set the 3/8-inch drive ratchet to tighten, and insert it into the square hole on the idler bracket Turn it toward the right side of the mower to loosen the belt tension
What does a belt keeper Rod do?
Description: The belt keeper rod goes next to the engine pulley and helps to guide the belt This part is available as an individual replacement It is made out of metal and may require a socket set and a wrench set while replacing this item
What are the signs of a bad belt tensioner?
Rust bleed and cracks Appearance: Rust is bleeding between arm and base or dripping from the tensioner Pulley bearing wear Pulley wear Tensioner assembly misalignment Tensioner noise Tensioner arm misalignment Excessive tensioner arm oscillation Binding or grinding tensioner arm movement
When should I replace my belt tensioner?
There is no recommended timeframe in which to replace your tensioner, especially as the belt itself usually needs replacing before the tensioner does However, you should inspect your tensioner each time you service your car to monitor its condition and replace it if necessary
How do you adjust the drive belt on a Craftsman riding lawn mower?
Push the belt keepers on the transaxle pulley down and slide the belt over the transaxle pulley Pull the slack from the back of the tractor (transaxle pulley) and slide the belt on to the stationary and clutch idlers This will increase the tension in the belt and hold it in place
How do you tighten the belt on a Craftsman riding lawn mower?
Although there are certain lawn mowers which allow it, you cannot tighten a drive belt on a Craftsmen lawn mower Instead, you will need to replace it To replace, remove the cutting deck, and pull the belt off the pulleys Replace with a new belt and reattach the deck to begin using again
Can you over tighten a belt tensioner?
Over-tightened belts can cause internal damage to the bearings inside the pulleys It can also cause overheating of the belts and premature wear Put the vehicle back together by replacing the components required to access the belt tensioners To test, operate the vehicle for several minutes and shut it off
Can you over tighten a pulley?
A belt shouldn’t be over-tightened Any bearing that the belt rotates on can be burned out by an over-tightened belt A pulley bearing can be ruined by an over-tightened timing belt
Can a mower belt stretch?
Yes, lawnmower belts can stretch Continuous wear due to regular operation can cause them to elongate over time When it stretches more than it should, it can result in the drive belts lose grip on the pulley system