Question: How To Change Belt On Sears Riding Lawn Mower

How many belts are on a Craftsman riding lawn mower?

The three primary belts found in a Craftsman mower are the drive belt, power clutch belt and arbor belt

How do you adjust the belt tension on a Craftsman riding lawn mower?

Push the belt keepers on the transaxle pulley down and slide the belt over the transaxle pulley Pull the slack from the back of the tractor (transaxle pulley) and slide the belt on to the stationary and clutch idlers This will increase the tension in the belt and hold it in place

Do you have to remove mower deck to replace belt?

To replace this belt, the deck should be off the lawn mower To remove the front of the belt from the engine pulley, you may have to remove the cap screw from the center of the pulley and PTO to the engine crankshaft

What size belt do I need for a craftsman?

AYP / Craftsman / Sears Drive Belt No AYP / Craftsman / Sears Drive Belt fits 42″ mowers, 12-18 HP Size: 1/2″ x 92-1/4″

How do you know if your lawn mower belt is bad?

How to tell if a mower belt ne​​eds replacement The belt has s​​​ide wall damage Mower belt edges should be smooth and even throughout the entire length of the belt The belt has a glazed or bu​rned sidewall Look at the belt edge that contacts the pulleys The belt is​​ cracked

How much is a drive belt for a Craftsman riding lawn mower?

Compare with similar items This item Replacement Riding Mower Drive Belt 138255 / 160855 Replacement for Craftsman 42″ & FITS POULAN HUSQVARNA Add to Cart Customer Rating 44 out of 5 stars (380) Price $1798 Shipping FREE Shipping on orders over $2500 shipped by Amazon or get Fast, Free Shipping with Amazon Prime

Why does the belt keep coming off my Craftsman riding mower?

Your Craftsman mower belt may come off if the belt has been stretched or shredded; the belt keepers and brackets have been bent, the spindles, pulleys or tensioner spring are damaged; or debris has been lodged in your deck

How do you adjust a tensioner pulley?

Turn the adjustment bolt on the side, top or bottom of the pulley counterclockwise with the ratchet and socket until the accessory belt is loose enough to remove Tighten the tensioner pulley by turning the adjustment bolt clockwise with the ratchet and socket until the belt is tight

Why does my belt keep slipping off my lawn mower?

A lawn mower belt keeps coming off the mower because the belt guides and brackets are out of adjustment; debris is collecting under your pulleys and tensioners; the brackets, bearings or bushings are damaged, or the mower belt is worn

How long is a craftsman 42 inch deck belt?

1015 Dimensions: Length : 1015 (in) Width : 05 (in)

How do you remove a pulley from a riding lawn mower?

Place a wrench onto the square end of the threaded screw and turn it clockwise As you turn it, the jaws pull the pulley up and off the spindle

Can you change the serpentine belt yourself?

You can replace a serpentine belt with ordinary hand tools But we don’t recommend it The spaces are often tight and the belt-driven devices difficult to reach The belt placement tool allowed us to remove and properly place the new belt without reaching down into the pulley area

Where is the belt tensioner located?

The belt tensioner is on the front of the engine, between the crankshaft and alternator pulleys

How long does a lawn mower belt last?

You shouldn’t need to replace belts every year, or more in one year A common cause of belt breakage is excessive grass clippings on the deck

How do you measure a mower deck belt?

Place one end of the tailor’s tape measure on the mark, then extend the tape measure around the inside circumference of the circle until you reach the mark with the other end of the tape measure Take your reading from the tape measure to determine the size of the belt

What size belt does a craftsman 46 inch deck?

AYP / Craftsman / Sears Deck Belt fits 46″ & 50″ Decks Size: 1/2″ x 88-3/4″

What size belt do I need for a 54 inch deck?

AYP / Craftsman / Sears Deck Belt fits 54″ cut mowers Size: 5/8″ x 142 1/2″

What size belt do I need for a 42 inch deck?

There’s no standard size for a 42-inch-cut riding mower Each model uses a different size belt To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length

Can a lawn mower belt stretch?

Yes, lawnmower belts can stretch Continuous wear due to regular operation can cause them to elongate over time When it stretches more than it should, it can result in the drive belts lose grip on the pulley system

How do I know if my lawn mower pulley is bad?

If a pulley is badly worn, it can cause a bad vibration from the cutting deck on your lawn tractor To check all your pulleys, start by removing the mower deck Next, remove the mandrel covers and belt, then check all the pulleys for play and roughness when spinning

What size drive belt does a craftsman LT1000 take?

Craftsman LT1000 917271814 Deck Belt Size 95″ or 955″May 5, 2016

What is a primary mower belt?

Primary blade drive belt connects the mower deck driven pulley to the electric clutch to turn the blades Wear work gloves to protect your hands when installing this part

Why does my belt keep coming off?

The serpentine belt need constant tension on the belt to keep it from coming off If the belt alignment is not aligned then the belt may come off When this is out of adjustment or the tensioner pulley itself is loose this may cause the belt to come off as you describe

Can you adjust belt tensioner?

Cars equipped with an automatic belt tensioner adjust themselves over time and do not require adjustment This article shows you the process to adjust drive belts on a pivot-style belt adjuster

How do I adjust the tension on my engine belt?

To correct the problem, tighten your belt Open the hood and locate the adjustment screw that controls tension on the serpentine belt Place the socket end of the socket wrench over the wing-nut and turn clockwise to apply tension Check the tension of the belt periodically Do a secondary check of the belt tension