Can you use 2 fish finders at the same time?
Any time you run two units with the same frequency there is a risk of interference However, with the modern noise rejection systems built into today’s fish finders, in most conditions when there is a unit on the front and back of the boat with the same frequencies, they will not interfere with each other
Can you run 2 fish finders off 1 transducer?
The chirp units nearly always can be run together because the 2d can be manually set to a variety of frequencies and the Side/Down can be run on either 455 or 800 One chirp and one non-chirp can probably also work since the chirp unit has some flexibility in the settings
Can you run 2 Lowrance units together?
The Lowrance Hook 2 Series cannot be linked together If you want a Lowrance unit that can be linked together you will need to upgrade to the Elite Ti series, Hds Gen 3 Series, or the Hds Carbon Series
Will 2 transducers interfere with each other?
If both transducers are using the same frequency, they will interfere with each other once you reach a water depth that allows the two beams to cross In shallow water, they may work together if the transducers are far enough apart Setting each unit on a different frequency will prevent interference
Can you put 2 transducers side by side?
You can mount SI/DI and high speed transducers side by side on the same side of the boat without any problems When they both transducers use the same frequency is when you may experience interference
Can you mount a transducer on the port side?
I mounted my Transducer on the port side so when I’m fishing its on my side If you can mount it 12 to 18 inches from your lower unit you should be fine It’s more important to have the transducer mounted properly
Can you run two Helix on transducer?
Yes via Ethernet I see you have a 360 and two displays now If you have all three connected via Ethernet, you can do it now Just turn Sonar OFF with one of the units—same as disconnecting the transducer
Can two Lowrance units share one transducer?
One transducer can not be used with two units simultaneously and return different images You will also get interference if you mount two “same frequency” transducers in the same area where their cone angles will overlap
Does NMEA 2000 Share Sonar?
Sonar cannot be shared over NMEA 2000 or NMEA 0183 networking The units do not have to be directly connected to each other, they can be bridged through other Ethernet capable units or devices, or a Network Expansion Port (NEP-2 000-10029-001)
How close together can you mount transducers?
Make sure there is nothing in front, behind, or to the side of the transducer that is closer than 12″ Do not mount the transducer where it could be damaged from trailering, launching, or storage
How far should a transducer be in the water?
Ensure the boat is in water greater than 2′ but less than the depth capability of the unit and the transducer is fully submerged Remember the sonar signal cannot pass through air If the unit is working properly gradually increase the boat speed to test high-speed performance
Can a transom mount transducer be used with inboard engines?
Question: The installation manual says the transom mount transducer is not recommended for large inboard engines Answer: You can mount it on an inboard boat, but it is not optimal because of the turbulence created by the propeller
Can you network Lowrance hook 7?
The Hook2 and Hook Reveal series are not designed to be networked with other units It is made for the angler that wants to fish with the basic features To enjoy the benefits of networking, the Elite and HDS products are recommended
How does NMEA 2000 work?
NMEA 2000 is used to create a system of connected electronic devices, typically amongst marine instruments, on a marine vessel The backbone serves as a central link between all devices connected to the network by powering each instrument which then relays digital information throughout the entirety of the system
Can you network HDS live to HDS Gen 2?
You might experience a few bugs on the Live if you do, and the Live will revert to legacy mode (Which basically means you have wasted quite a bit of money as it will act like a HDS Gen 2 just with the better screen) So yes, it can be done
Is it bad to turn on fish finder out of water?
It is not recommended to run a FishFinder and transducer on a boat that is not in the water as you will not get any readings from the transducer Without the water, the transducer could burn out and have issues if left running for an extended period of time out of the water
Can you mount transducer on left side of boat?
The location should be as close to the center of the boat as possible, but on the side of the downward swing the propeller On the majority of boats, this will be on the starboard (right) side
Where is the best place to mount a transducer?
Transducer placement should be aft and close to the centerline It needs to be located low enough that the transducer is in the water at all times Consider items such as the lifting strap placement into the location as well as trailer bunks and rollers if it is a trailered vessel
Can you split a transducer cable?
Yes, the transducer cable can be cut However, if the transducer came with a connector do not cut it off The molded on connector is waterproof You need to cut and splice the cable away from the connector using Airmar’s splash-proof Junction Box